Reyee Wireless PoC Guide V1.0
1.1 Management
1.1.1 eWeb
Testing project | eWeb |
Testing purpose | Enable WEB and log into device successfully |
Testing procedure and expected results |
1. Connect PC with Reyee Wireless AP through net cable as shown above. (In this example, port LAN2 is connected)
2, Select DHCP mode on PC to get an IP address. In this example, IP address of PC is 192.168.110.52.
1. Enter the IP of Reyee AP 192.168.110.39 in browser browser must be IE and other major browsers and open compatible mode. 2. Verify Web access. (Expected interface is shown above)
|
Measured record | Login eWeb successfully |
Testing conclusion | eWeb can be easily opened by simply enter 192.168.110.39 in browser |
1.2 Basic Feature
1.2.1 LAN Port VLAN
Testing Project | LAN Port VLAN |
Testing Purpose | Create VLAN via LAN Port |
Testing procedure and expected results | 1. Power on the Reyee AP, connect AP to the PC1 by net cable
2. In Wireless / LAN Ports tap, enter VLAN ID to set up a new VLAN Then click save button to save the setting. (In this example, VLAN 100 is created).
|
Measured record | In this example, VLAN 1 and VLAN 2 are created correspondingly |
Testing conclusion | By taking the advantage of LAN Port VLAN, we can enable multiple virtual local area network easily |
1.2.2 Roaming
Testing project | Roaming |
Testing purpose | Test roaming feature between Reyee AP products |
Testing procedure and expected results |
1. Connect two Aps to EG. (In this example, note that AP1 is in one room and AP2 is in another room) 2. Create 1st Wi-Fi from AP1 in Wireless >> WiFi configuration tap as shown below 3. Pick a device and connect to the Wi-Fi we created above In this example, iPhone is connected to this Wi-Fi. 4. Similarly, create the same Wi-Fi from AP2 in Wireless >> WiFi configuration tap as shown below. If L3 roaming, need enable the L3 roaming button on eWeb 5. Now walk into the room where AP2 placed and connect to the 2nd Wi-Fi we created above. Then walk back to the room where AP1 placed 6. Try to use the Wi-Fi MoHo to test the roaming and record the roaming status and the delay |
Measured record | When we walk into the area near AP1, the Wi-Fi switches automatically from the 1st Wi-Fi to the 2nd Wi-Fi |
Testing conclusion | By taking advantage of Roaming feature, the Wi-Fi connected to user’s device can be switched from another adjacent Wi-Fi automatically |
1.2.3 Coverage Test
Testing project | Coverage of AP | |||||||||||||||||||||||||
Testing purpose | Test Reyee AP coverage | |||||||||||||||||||||||||
Testing procedure and expected results | 1. Connect 1 AP to EG
2. Create the SSID on dual-band, configure the AP power to High 3. Connect to AP with SSID in different distance and obstruct. Test the Rssi with WiFi MoHo and test the throughput with speedtest
|
|||||||||||||||||||||||||
Measured record | Record the 3 times test result
|
|||||||||||||||||||||||||
Testing conclusion |
1.2.6 Guest Wi-Fi
Testing project | Guest Wi-Fi |
Testing purpose | Set a Guest Wi-Fi to allow guests get access to Wi-Fi temporarily |
Testing procedure and expected results |
1. Open Guest Wi-Fi configuration from Wireless >> WiFI Menu 2. Enable the Guest Wi-Fi function then enter the SSID of Guest Wi-Fi. The Other settings are optional. Then click Save to create this Guest Wi-Fi In this example, SSID os Guest Wi-Fi is @Guest-2021 as shown below. 3. Pick a device to connect the Guest Wi-Fi we created above Expected results: 4. Try to ping other users that connect to other SSID |
Measured record | With Guest Wi-Fi @Guest-2021 created, guests can get access to Guest Wi-Fi successfully. |
Testing conclusion | Guest Wi-Fi feature on Reyee Wireless brings friendly user experience to guests |