Reyee Wireless PoC Guide V1.0

 โพสต์เมื่อ : 27 ส.ค 2567 เวลา 6:11 น.
RAP820-v3-06-1030x1030

1.1 Management

1.1.1 eWeb
Testing projecteWeb
Testing purposeEnable WEB and log into device successfully
Testing procedure and expected results
  1. Connect PC with Reyee Wireless AP through network cable (e.g., connect to LAN2 port).
  2. Select DHCP mode on PC to obtain an IP address (e.g., 192.168.110.52).
  3. Enter the IP address of Reyee AP (192.168.110.39) in a web browser. Ensure the browser is IE or another major browser in compatibility mode.
  4. Verify web access. The expected interface should appear as intended.
Measured recordLogin to eWeb successfully.
Testing conclusioneWeb can be easily accessed by entering 192.168.110.39 in the browser.

1.2 Basic Feature

1.2.1 LAN Port VLAN
Testing ProjectLAN Port VLAN
Testing PurposeCreate VLAN via LAN Port
Testing procedure and expected results1. Power on the Reyee AP, connect AP to the PC1 by network cable.
2. In Wireless / LAN Ports tab, enter VLAN ID to set up a new VLAN.
Then click the save button to save the setting.
(In this example, VLAN 100 is created).
Measured recordIn this example, VLAN 1 and VLAN 2 are created correspondingly.
Testing conclusionBy taking advantage of LAN Port VLAN, we can enable multiple virtual local area networks easily.
1.2.2 Roaming
Testing projectRoaming
Testing purposeTest roaming feature between Reyee AP products
Testing procedure and expected results1. Connect two APs to EG. (In this example, note that AP1 is in one room and AP2 is in another room)

2. Create 1st Wi-Fi from AP1 in Wireless >> WiFi configuration tab as shown below.

3. Pick a device and connect to the Wi-Fi we created above.

In this example, an iPhone is connected to this Wi-Fi.

4. Similarly, create the same Wi-Fi from AP2 in Wireless >> WiFi configuration tab as shown below. If L3 roaming, enable the L3 roaming button on eWeb.

5. Now walk into the room where AP2 is placed and connect to the 2nd Wi-Fi we created above. Then walk back to the room where AP1 is placed.

6. Use the Wi-Fi MoHo to test the roaming and record the roaming status and the delay.
Measured recordWhen we walk into the area near AP1, the Wi-Fi switches automatically from the 1st Wi-Fi to the 2nd Wi-Fi.
Testing conclusionBy taking advantage of the Roaming feature, the Wi-Fi connected to the user’s device can be switched automatically from one adjacent Wi-Fi to another.
1.2.3 Coverage Test
Testing projectCoverage of AP
Testing purposeTest Reyee AP coverage
Testing procedure and expected results

Connect 1 AP to EG

Create the SSID on dual-band, configure the AP power to High

Connect to AP with SSID at different distances and obstacles. Test the RSSI with WiFi MoHo and test the throughput with speedtest

Measured recordRecord the 3 times test results
DistanceRSSIDownloadUpload
110M
220M-62dBm12.620.76
330M
Average
Testing conclusion
1.2.4 Guest Wi-Fi
Testing projectGuest Wi-Fi
Testing purposeSet a Guest Wi-Fi to allow guests to access Wi-Fi temporarily
Testing procedure and expected results

Open Guest Wi-Fi configuration from Wireless >> WiFi Menu

Enable the Guest Wi-Fi function then enter the SSID of Guest Wi-Fi. Other settings are optional. Then click Save to create this Guest Wi-Fi

Pick a device to connect to the Guest Wi-Fi we created above

Try to ping other users that connect to another SSID

Measured recordWith Guest Wi-Fi @Guest-2021 created, guests can get access to Guest Wi-Fi successfully.
Testing conclusionGuest Wi-Fi feature on Reyee Wireless brings a friendly user experience to guests.